Just How to Replace a Bathtub in Your Bathroom
Just How to Replace a Bathtub in Your Bathroom
Blog Article
Just how do you really feel when it comes to Tools You Need to Install a New Bathtub ?
Setting up a tub isn't specifically rocket science, yet it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably difficult job. If the old tub is easily accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old tub and place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the work and fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you mount a new tub in your washroom if you have already acquired a new tub as well as do not require to change the plan of your previous water pipes.
Your tools and material list should make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome as a result of the restricted access that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to proceeding to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the producer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former type needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Using both wooden boards under its feet, position the bathtub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Switch on the water as well as inspect all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, take care of the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of once as this will certainly resolve it right into its final setting.
Getting ready for the Installment
To start with, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with wetness as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are sold in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can fracture relatively early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the market. It is a good idea to fit the tiles making use of water-resistant or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that editorial about How to Install a Bathtub from someone on another website. Do you know someone else who is excited about the subject? Be sure share it. Thanks for taking the time to read it.
Schedule Free Estimate Report this page